Starting Small... Building Big! With Alban CAT Construction Equipment...

Learn More
Specification Summary
Minimum Rating 800.0 bhp
Minimum Rating 800 BHP
Maximum Rating 1150.0 bhp
Maximum Rating 1150 BHP

Engine Specifications

Minimum Rating
800.0 bhp
Minimum Rating
800 BHP
Maximum Rating
1150.0 bhp
Maximum Rating
1150 BHP
Emissions
U.S. EPA Non-road Tier 2
Emissions
U.S. EPA Non-road Tier 2
Rated Speed
2100.0 RPM
Rated Speed
2100 r/min
Bore
5.4 in
Bore
5.4 in
Stroke
6.0 in
Stroke
6 in
Displacement
1658.0 in3
Displacement
1658 in³
Aspiration
Turbocharged-Aftercooled
Aspiration
Turbocharged-Aftercooled
Governor and Protection
ADEM A3
Engine Weight, net dry
6382.0 lb
Engine Weight - Net Dry
6382 lb
Oil Change Interval
250
Rotation (from flywheel end)
Counterclockwise
Oil Change Interval
250
Rotation from Flywheel End
Counterclockwise
Flywheel and Flywheel Housing
SAE No. 0 or SAE No. 1
Flywheel and Flywheel Housing
SAE No. 0 or SAE No. 1
Flywheel Teeth
136 (SAE 0), 113 (SAE 1)
Flywheel Teeth
136 (SAE 0), 113 (SAE 1)

Capacity for Liquids

Minimum Cooling System - Engine Only
14.5 gal (US)

Dimensions

Length
75.5 in
Length
75.5 in
Width
57.6 in
Width
57.6 in
Height
52.0 in
Height
52 in
  • Air Inlet System
    • Dual turbochargers side or rear mounted — inlet 152.4 mm (6 in.) hose connection
  • Control System
    • Electronic governing, PTO speed control
    • Programmable ratings
    • Cold mode start strategy
    • Automatic altitude compensation
    • Power compensation for fuel temperature
    • Programmable low and high idle and TEL
    • Electronic diagnostics and fault logging
    • Engine monitoring and protection system (speed, temperature, pressure)
    • J1939 Broadcast (diagnostic, engine status, and control)
  • Cooling System
    • Thermostats and housing — outlet LH vertical orientation
    • Jacket water pump — gear-driven, centrifugal RH
  • Exhaust System
    • Exhaust manifold — dry, heat shields
    • Dual turbo — rear turbo exhaust, full marmon connection 127 mm (5 in.), maximum load 10 kg for direct
    • Water-cooled center sections
  • Flywheels and Flywheel Housings
    • SAE No. 0 or SAE No. 1
    • SAE standard rotation
  • Fuel System
    • MEUI system
    • Fuel filter, RH ( 2 micron high performance)
    • Fuel transfer pump
    • Fuel priming pump (optional electric priming pump)
  • Lube System
    • Crankcase breather — rear mounted
    • Oil cooler — RH
    • Side turbo — oil filler in RH front gear case
    • Rear turbo — oil filler in RH valve cover
    • Oil level gauge — RH
    • Oil filter — RH
    • Oil pan rear sump
  • Mounting System
    • Front support — narrow
  • Power Take-Offs
    • Crankshaft pulley — 203.2 mm (8 in), 5 grooves 15.9 mm (.63 in) wide; 292.1 mm (11.5 in.) 1 groove 15.9 mm (.63 in.) wide
  • General
    • Vibration damper
    • Paint — Cat yellow
    • Lifting eyes
    • Automatic variable timing, electronic
    • Electronic installation kit 70-pin connector (connectors, pins, sockets)
  • Air Inlet System
    • Air lines
    • Air cleaners
    • Precleaners
  • Charging System
    • Battery chargers
    • Charging alternators
    • Alternator mountings
  • Circuit Breakers
    • Circuit breaker mounting
  • Cooling System
    • Blower fans
    • Suction fans
    • Radiators
  • Exhaust System
    • Muffler
  • Fuel Systems
    • Electric fuel priming pump
  • Instrumentation
    • Gauges and instrument panels
  • Lube System
    • Lubricating oil
    • Oil pan
    • Oil filter
  • Mounting System
    • Engine supports
  • Power Take-Offs
    • Hydraulic pump drives
    • Pulley
    • Auxiliary drive
  • Starting System
    • Electric starting motor
    • Battery sets - 24V
    • Battery cable
    • Battery rack
    • Starting aids
  • Packaging
    • Overseas preservation
    • Storage preservation
    • Export packaging