Starting Small... Building Big! With Alban CAT Construction Equipment...

Learn More
Specification Summary
Minimum Rating 800.0 bhp
Minimum Rating 800 BHP
Maximum Rating 1500.0 bhp
Maximum Rating 1500 BHP

Engine Specifications

Minimum Rating
800.0 bhp
Minimum Rating
800 BHP
Maximum Rating
1500.0 bhp
Maximum Rating
1500 BHP
Emissions
U.S. EPA Non-road Tier 2
Emissions
U.S. EPA Non-road Tier 2
Rated Speed
2100.0 RPM
Rated Speed
2100 r/min
Bore
5.7 in
Bore
5.7 in
Stroke
6.4 in
Stroke
6.4 in
Displacement
1953.0 in3
Displacement
1953 in³
Aspiration
Turbocharged-Aftercooled
Aspiration
Turbocharged-Aftercooled
Governor and Protection
ADEM A3
Engine Weight, net dry
5040.0 lb
Engine Weight - Net Dry
5040 lb
Oil Change Interval
250
Rotation (from flywheel end)
Counterclockwise
Oil Change Interval
250
Rotation from Flywheel End
Counterclockwise
Flywheel and Flywheel Housing
SAE No. 0 or SAE No. 1
Flywheel and Flywheel Housing
SAE No. 0 or SAE No. 1
Flywheel Teeth
136 (SAE 0), 113 (SAE 1)
Flywheel Teeth
136 (SAE 0), 113 (SAE 1)

Capacity for Liquids

Minimum Cooling System - Engine Only
14.5 gal (US)

Dimensions

Length
75.5 in
Length
75.5 in
Width
85.0 in
Width
85 in
Height
52.0 in
Height
52 in
  • Air Inlet System
    • Quad turbocharger — 3 cylinder exhaust to each turbo
    • Connections configured for ATAAC (Air-to-Air-Aftercooled)or remote heat exchanger
  • Control System
    • ADEM A4 electronic control module
    • Electronic governing, PTO speed control
    • Customer programmable ratings
    • Cold mode start strategy
    • Automatic altitude compensation
    • Automatic fuel temperature compensation
    • Programmable low and high idle, and top engine speedlimit
    • Electronic diagnostics and fault logging
    • Engine monitoring system
    • SAE J1939 broadcast (diagnostic and engine status)
  • Cooling System
    • Gear-driven centrifugal jacket water pump — RH
    • Integrated thermostat and housing
    • Engine oil cooler
    • Optional installed transmission oil cooler
  • Exhaust System
    • Exhaust manifold — dry
    • Two vertical exhaust outlets (front and rear)
  • Fuel System
    • MEUI
    • Fuel priming pump
    • Fuel transfer pump
    • Primary and secondary fuel filter — RH configured forremote mounting (installed RH on shipping plate)
  • Flywheels and Flywheel Housing
    • SAE No. 0 or SAE No. 1 flywheel iron housing
    • SAE No. 0 or SAE No. 1 flywheel
    • Optional transmission adapter
  • Lube System
    • Crankcase breather
    • Oil filter — RH standard, optional LH or remote mountservice
    • Oil level gauge — RH standard, optional LH or dualservice
    • Oil filler — RH standard, optional LH or dual service
    • Shallow oil pan, rear sump
  • Mounting System
    • Trunnion front support
    • Vertical and horizontal pads on rear flywheel housing
  • Protection System
    • 24V electronic
    • Engine overspeed with optional air shut-offs withindicators
    • Low engine oil pressure
    • Fuel filter restriction
    • Fuel temperature
    • High engine coolant temperature
    • Low engine coolant temperature
  • General
    • Vibration damper and optional guard
    • Lifting eyes
    • Optional customer wiring connector
    • Service tool connector
    • Paint — Cat yellow
  • Air Inlet System
    • Air cleaner
    • Air inlet adapters
    • Turbocharger outlet adapters
    • Air lines
  • Charging System
    • Battery chargers
    • Charging alternators
    • Alternator mounting
    • Circuit breakers and mountings
  • Cooling System
    • Dry charge coolant conditioners
    • Thermostat housing
    • Coolant level sensor
    • Radiator
    • Blower fans
    • Suction fans
    • Fan adapters
    • Fan drives
  • Emissions
    • IMO certifications
  • Exhaust System
    • Elbows
    • Mufflers
  • Fuel Systems
    • Electric fuel priming pump
  • Instrumentation
    • Customer management device
    • Interconnect harness
    • Gauges and instrument panels
  • Lube System
    • Oil pans
    • Oil service side
    • Oil level gauge
    • Oil filters
    • Lubricating oils
  • Mounting System
    • Structural steel base
    • Engine support — front
    • Engine support — rear
  • Power Take-Offs
    • Auxiliary drive
    • Damper pulley
    • Hydraulics gear pumps
  • Protection System
    • Mechanical shutoffs
    • Solenoid shutoffs
  • Starting System
    • Electric starting motors – 12V, 24V
    • Battery sets – 24V
    • Battery cable
    • Battery rack
    • Starting aids
  • Transmission Arrangement
    • Transmissions water lines
    • Transmissions cooler