Starting Small... Building Big! With Alban CAT Construction Equipment...

Learn More
3516C (HD) CI/D2 Hazardous Location Specifications
Minimum Rating 2625 kV·A
Maximum Rating 2625 kV·A
Emissions EPA Tier 2, IMO Tier II
Oil Change Interval 1000.0 hr

Engine Specifications

Minimum Rating
2625 kV·A
Maximum Rating
2625 kV·A
Emissions
EPA Tier 2, IMO Tier II
Oil Change Interval
1000.0 hr
Aspiration
Dual Turbocharged-Aftercooled
Fuel System
EUI
Stroke
8.5 in
Bore
6.7 in
Displacement
4760.0 in3
Engine Control
ADEM A4
Weight
38581 lb
Aspiration
Dual Turbocharged-Aftercooled
Bore
6.7 in
Displacement
4760 in³
Fuel System
EUI
Stroke
8.5 in

Dimensions

Length
264.0 in
Height
100.0 in
Width
78.0 in
Height
100 in
Length
264 in
Width
78 in

Capacity for Liquids

Cooling System (Engine)
62.0 gal
Lube Oil System (Refill)
107.0 gal
Cooling System - Engine
62 gal (US)
Lube Oil System - Refill
107 gal (US)
  • AIR INLET SYSTEM
    • Aftercooler core, corrosion resistant (air side)
    • Air cleaner, regular duty with service indicators
    • Dual turbochargers, rear mounted
  • CONTROL SYSTEM
    • Dual Caterpillar A4 electronic engine control with electronic unit injector fuel system and rigid wiring harness.
    • 24 VDC (less than 10A) to be provided by customer at Power Distribution Panel to power engine electrical system.
  • COOLING SYSTEM
    • Jacket water (JW) engine cooling and two-stage jacket water/separate circuit (SCAC) charge air cooling
    • To ensure compliance in use, radiators or heat exchangers must be capable of rejecting sufficient heat to allow proper engine operation at worst site conditions.
    • The radiator or heat exchanger must supply 48C (118 F)
    • SCAC cooling water to the aftercooler inlet of at least 200 gal/min at ambient temperature of 30C and at site conditions (including altitude considerations)
  • EXHAUST SYSTEM
    • Dry gas-tight exhaust manifolds with heat shields, dual turbochargers with water-cooled bearings and heat shields.
    • Exhaust outlet: 305 mm (12 in) round flanged outlet, vertical orientation
  • FLYWHEELS & FLYWHEEL HOUSINGS
    • Flywheel, SAE No. 00, 183 teeth Flywheel housing, SAE No. 00
    • Flywheel housing, SAE No. 00
    • SAE standard rotation
  • FUEL SYSTEM
    • Duplex Fuel filter, LH service. Simplex fuel filter, RH service
    • Fuel transfer pump
    • Fuel priming pump, RH
    • Electronically Controlled Unit Injectors
    • Customer connection located at lower right front of engine
    • SOLAS shielding
  • INSTRUMENTATION
    • Engine mounted instrument panel with four position switch, over speed shutdown notification light, emergency stop notification light, graphical display unit for analog or digital display of: oil and fuel pressure, oil and fuel filter differential, system DC voltage, exhaust and water temperature, air inlet restriction, service meter, engine speed, fuel consumption (total and instantaneous)
  • LUBE SYSTEM
    • Top mounted crankcase breather, RH oil filter, RH oil filler, gear type oil pump, deep sump oil pan, recommended use of Caterpillar Diesel Engine Oil 10W30 or 15W40
  • MOUNTING SYSTEM
    • Mounting rails and isolation system based on customer request
  • ELECTRICAL SYSTEM
    • MCS certified Class I / Divison 2
    • Low Smoke Zero Halogen Wiring Harness
  • PROTECTION SYSTEM
    • A-III Electronic Monitoring System provides customer programmable engine de-ration strategies to protect against adverse operating conditions
    • Emergency stop push button (located in Electronic Instrument Panel) Safety shutoff protection for oil pressure and water temperature, over speed protection
  • HAZARDOUS LOCATION
    • Only electrical system is hazardous environment certified
    • NEC 500 Class I Division 2 for gas groups C and D
    • Temperature class is T3 for ambient temperatures from -10 C to 50 C
    • Class I/ Division 2 CMPD
  • GENERATOR AND GENERATOR ATTACHMENTS
    • Class I / Division 2 designed to customer's specifications
    • Insulation for harsh environment protection