Chat with us, powered by LiveChat

Starting Small... Building Big! With Alban CAT Construction Equipment...

Learn More
C11 ACERT™ Dry Manifold Engine Specifications
Minimum Rating 325 BHP
Maximum Rating 450 BHP
Governor and Protection Electronic (ADEM™ A3)
Aspiration Turbocharged-Aftercooled

General Specifications

Minimum Rating
325 BHP
Maximum Rating
450 BHP
Governor and Protection
Electronic (ADEM™ A3)
Aspiration
Turbocharged-Aftercooled
Displacement
681 in³
Flywheel and Flywheel Housing
SAE 1 or SAE 2
Flywheel Teeth
113 (SAE 1), 138 (SAE 2)
Rotation from Flywheel End
Counterclockwise
Stroke
5.51 in
Bore
5.12 in

Emissions

Emissions
EPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA

Dimensions

Length
47.3 in.
Length
47.3 in
Width
41.6 in.
Width
41.6 in
Height
46.3 in.
Height
46.3 in
Weight
1967.0 lb
Weight
1967 lb

Capacity for Liquids

Lube Oil System (refill)
9.0 gal
Lube Oil System - Refill
9 gal (US)
  • Air Inlet System
    • Turbocharger, mid-mounted
    • Air inlet elbow 90°, 104.5 mm (4.11" OD) hose connection
  • Control System
    • Electronic governing, PTO speed control
    • Programmable ratings
    • Cold mode start strategy
    • Automatic altitude compensation
    • Power compensation for fuel temperature
    • Programmable low and high idle and TEL
    • Electronic diagnostics and fault logging
    • Engine monitoring system — speed, temperature, pressure
    • J1939 Broadcast — diagnostic and engine status
  • Cooling System
    • Thermostats and housing
    • Jacket water pump — gear-driven
    • Front water pump inlet
  • Exhaust System
    • Exhaust manifold — dry
    • Front turbo exhaust
  • Flywheels and Flywheel Housings
    • See Mandatory Options
  • Fuel System
    • Electronic unit injector
    • Fuel filter — secondary, mid-mount, (LH 2 micron high performance)
    • Fuel transfer pump — front
    • Fuel priming pump — LH mid-mount
  • Lube System
    • Crankcase breather
    • Oil cooler
    • Oil filter — RH
    • Oil pan — front sump, 40 L capacity
    • Oil filler — LH front
    • Oil dipstick — LH mid-mount
    • Oil pump
    • Oil valve sampling — on oil filter base
  • Power Take-Offs
    • Crankshaft pulley and damper — 250 mm (9.84 in), 2 grooves 22.3 mm (.87 in) width
    • Hydraulic pump drive — SAE A, 11 tooth
    • 1.41:1 drive ratio — counterclockwise rotation (45 lb-ft capacity)
  • General
    • Vibration damper
    • Paint — Cat yellow
    • Lifting eyes
    • Automatic variable timing, electronic
    • Electronic installation kit (connectors, pins, sockets)
    • Literature
  • Mandatory Options
    • Flywheel housing or rear PTO
    • Throttle position sensor
    • Primary filter/water separator
  • Air Compressor
    • Expansion chamber
    • Governors
    • Fittings
  • Air Inlet System
    • Air cleaners
    • Precleaners
    • Turbo air inlet
    • Air lines
  • Belt-Driven Accessories
    • Refrigerant compressor and mounting
  • Charging System
    • Charging alternators
    • Alternator mountings
    • Alternator guard
    • Alternator accessories
  • Control System
    • Connection
  • Cooling System
    • Radiator — installed
    • Fan drive f/u/w Caterpillar installed radiator
    • Fan drive pulleys f/u/w customer-supplied radiators
    • Coolant conditioner
    • Water lines — pump inlet
    • Fan drive mountings
    • Fan height instructions
    • Fan adapters for suction fans
    • Fan adapters for blower fans
    • Suction fans
    • Blower fans
    • Coolant level sensor
    • Aftercooler lines
  • Exhaust System
    • Muffler
    • Flexible fitting
    • Elbows
    • Straight exhaust adapter
    • Flange
    • Pipe
    • Rain cap
    • Clamp
  • Fuel System
    • Fuel lines
    • Fuel cooler
    • Fuel fitting — fuel return and supply connections
    • Flexible fuel lines
  • Instrumentation
    • Gauges and instrument panels
    • Voltmeters
    • Gauge mounting
    • Ammeter
  • Lube System
    • Oil pan
    • Oil pan drain
    • Oil level gauges
    • Oil filter — bypass
    • Oil filter — remote
    • Lubricating oil
    • Oil filler
    • Fumes disposal
  • Mounting System
    • Front and rear engine supports
    • Structural steel base
  • Power Take-Offs
    • Crankshaft pulleys
    • Crankshaft pulley — stack-on
    • Output flange
    • Flywheel stub shaft
    • Front stub shaft
    • Hydraulic pump drive
    • Hydraulic pumps — front
    • Hydraulic pumps — rear
    • Enclosed Clutch
    • Clutch Support
  • Protection System
    • Air shutoff
    • Air shutoff switch
  • Starting System
    • Electric starting motors — 12 Volt, 24 Volt
    • Starting aids
    • Battery sets — 24 Volt, dry
    • Battery cable
    • Battery rack
  • Transmission Arrangement
    • Transmission cooler