Starting Small... Building Big! With Alban CAT Construction Equipment...

Learn More
C13 ACERT™ Dry Manifold Petroleum Engine Specifications
Minimum Rating 385 BHP
Maximum Rating 520 BHP
Governor and Protection Electronic (ADEM™ A3)
RPM 2100 r/min

General Specifications

Minimum Rating
385 BHP
Maximum Rating
520 BHP
Governor and Protection
Electronic (ADEM™ A3)
RPM
2100 r/min
Aspiration
Turbocharged-Aftercooled
Displacement
760 in³
Flywheel and Flywheel Housing
SAE 1
Flywheel Teeth
113
Rotation from Flywheel End
Counterclockwise
Stroke
6.2 in
Bore
5.1 in

Emissions

Emissions
EPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA

Dimensions

Length
47.3 in.
Length
47.3 in
Width
39.9 in.
Width
39.9 in
Height
46.7 in.
Height
46.7 in
Weight
1976.0 lb
Weight
1976 lb

Capacity for Liquids

Lube Oil System (refill)
9.0 gal
Lube Oil System - Refill
9 gal (US)
Cooling System
3.8 gal (US)
  • Air Inlet System
    • Turbocharger, mid-mounted
    • Air inlet elbow 90°, 104.5 mm (4.11" OD) hose connection
  • Control System
    • Electronic governing, PTO speed control
    • Programmable ratings
    • Cold mode start strategy
    • Automatic altitude compensation
    • Power compensation for fuel temperature
    • Programmable low and high idle and TEL
    • Electronic diagnostics and fault logging
    • Engine monitoring system — speed, temperature, pressure
    • J1939 Broadcast — diagnostic and engine status
  • Cooling System
    • Thermostats and housing
    • Jacket water pump — gear-driven
    • Front water pump inlet
  • Exhaust System
    • Exhaust manifold — dry
    • Front turbo exhaust
  • Flywheels and Flywheel Housings
    • See Mandatory Options
  • Fuel System
    • Electronic unit injector
    • Fuel filter — secondary, mid-mount, (LH 2 micron high performance)
    • Fuel transfer pump — front
    • Fuel priming pump — LH mid-mount
    • Fuel fitting — fuel return connection: straight No. 8, 5/8-18
  • Lube System
    • Crankcase breather
    • Oil cooler
    • Oil filter — RH
    • Oil pan — front sump, 40 L capacity
    • Oil filler — LH front
    • Oil dipstick — LH front
    • Oil pump
    • Oil valve sampling — RH rear engine side
  • Power Take-Offs
    • Crankshaft pulley and damper — 250 mm (9.84 in), 2 grooves 22.3 mm (.87 in) width
    • Hydraulic pump drive — SAE A, 11-tooth
    • 1.41:1 drive ratio — counterclockwise rotation (45 lb-ft capacity)
  • General
    • Vibration damper
    • Paint — Cat yellow
    • Lifting eyes
    • Automatic variable timing, electronic
    • Electronic installation kit (connectors, pins, sockets)
    • Literature
  • Mandatory Options
    • Flywheel housing or rear PTO
    • Throttle position sensor
    • Primary filter/water separator
  • Air Compressor
    • Air compressors
    • Air chambers
    • Air compressor governors
  • Air Inlet System
    • Air cleaners
    • Precleaners
    • Air lines
    • Air inlet gasket
  • Belt-Driven Accessories
    • Refrigerant compressor and mounting
  • Charging System
    • Charging alternators
    • Alternator mountings
    • Alternator guard
    • Alternator accessories
  • Control System
    • Connection
  • Cooling System
    • Radiator — installed
    • Fan drive f/u/w Caterpillar installed radiator
    • Fan drive pulleys f/u/w customer-supplied radiators
    • Coolant conditioner
    • Water lines — pump inlet
    • Fan drive mountings
    • Fan height instructions
    • Fan adapters for suction fans and blower fans
    • Suction fans and blower fans
    • Coolant level sensor
    • Aftercooler lines
  • Exhaust System
    • Muffler
    • Flexible fitting
    • Elbows, flange, pipe, clamp
    • Straight exhaust adapter
  • Fuel System
    • Fuel lines for fuel filter
    • Fuel cooler
    • Fuel fitting — fuel return connection
    • Flexible fuel lines
  • Instrumentation
    • Gauges and instrument panels
    • Voltmeters
    • Gauge mounting
    • Ammeter
  • Lube System
    • Oil pan
    • Oil pan drain
    • Oil level gauges
    • Oil filter — bypass and remote
    • Lubricating oil
    • Oil filler
    • Fumes disposal
  • Mounting System
    • Front and rear engine supports
    • Structural steel base
  • Power Take-Offs
    • Crankshaft pulleys
    • Crankshaft pulley — stack-on
    • Output flange
    • Flywheel stub shaft
    • Front stub shaft
    • Hydraulic pump drive
    • Hydraulic pumps — front and rear
    • Enclosed clutch
    • Clutch support
  • Protection System
    • Air shutoff
    • Air shutoff switch
  • Starting System
    • Starting System
    • Starting aids
    • Battery sets — 24 Volt, dry
    • Battery cable
    • Battery rack
  • Transmission Arrangement
    • Transmission cooler